5000 Watt Inverters – Scimitar 5000 Series

Scimitar

Get a Quote
5000 watt inverter

Product Information

The SIMITAR 5000 Series are 5000 watt inverters which are 19” rack-mountable and only 3RU high. Different models operate from a 24 or 48 VDC source and produce a sine-wave 115 or 230 VAC output.

The tightly regulated low distortion 50 or 60Hz sine wave is produced by DSP controlled power circuits using an advanced high frequency, pulse-width modulation technique which achieves up to 92% efficiency.

A built-in Static Transfer Switch allows connection of a utility or other AC power source which can be switched to the load automatically in the event that the inverter switches off.
In normal operation these inverters isolate the load from wide voltage swings , transients and noise usually present in the AC utility and which can cause equipment reliability problems.

Output voltage and frequency are programmable from the front panel, as well as Baud Rate for the RS232 communications interface which can be used for remote monitoring.

TWO YEAR WARRANTY

Features and Options
  • 19-Inch x 3RU Rack Mounting
  • 5000W Output Capacity
  • 115VAC or 230VAC Output
  • 50 or 60Hz Low Distortion Sine Wave
  • 24 or 48 VDC Input
  • -20 to +50°C Operating Temperature
  • Static Transfer Switch Built-in
  • Adjustable Output Voltage
  • Programmable Frequency (DIP switch)
  • Powers Reactive Loads
  • LED Status Display
  • Relay Alarm Output
SPECIFICATIONS
 
INPUT
Voltage

24VDC (20-32VDC)
48VDC (42-62VDC)
Current (max.) 295A @ 24V
137A @ 48V
 
OUTPUT
Voltage

100-120VAC (adjustable)
200-240VAC (adjustable)
Power 5000W continuous | 10000W peak
Surge Rating 5200W for 3 minutes
Frequency 50Hz or 60Hz ±0.05% (switch selectable)
Efficiency 85-92% depending on model
Output Waveform Pure Sine Wave <3% THD (R Load)
 
TRANSFER FUNCTION (-STS OPTION)
AC Input Range 90-130VAC (110VAC nominal)
180-260VAC (230VAC nominal)
Frequency 47-63Hz
Transfer Time 4-6mS
Alarm Relay Form-C dry contacts, indicates presence of AC Utility supply
 
OTHER TECHNICAL DATA
Protection Output Overload; Output Short Circuit; Input Reverse Polarity (fuse); Input Undervoltage; Input Overvoltage; Over Temperature
Alarms General alarm signal activated by an open photo-relay if in fault mode, available at rear signal connector
Display OVP - UVP - OTP - OLP - VAC - AMP - WATT - VDC - TEMP - Hz
Control Port RS232C - Baud Rates - 2400, 4800, 9600, 19200 (switch selectable)
SNMP (Option) Operates in conjunction with NetAgent UPS SNMP Agent
Temperature Range Operating: -20°C to +50°C
Storage: -30°C to +70°C
MTBF > 98,000 hrs @ 25°C ambient, nominal output voltage & full load
 
DESIGN STANDARDS
Safety EN60950-1
EMC

120VAC Models:
FCC CFR Title 47 Part 15 Subpart B: 2008 Class A
CISPR 22: 2005
ANSI C63.4: 2003

230VAC Models:
EN55022:2006+A1: 2007, Class A
EN55024: 1998+A1: 2001+A2: 2003
EN61000-3-2: 2006
EN61000-3-3: 1995+A1: 2001+A2: 2005
IEC61000-4-2 Ed. 1.2: 2001-04
IEC61000-4-3 Ed. 3.0: 2006
IEC61000-4-4: 2004
IEC61000-4-5 Ed. 2.0: 2005
IEC61000-4-6 Ed. 2.2: 2006
IEC61000-4-8 Ed. 1.1: 2001-03
IEC61000-4-11 2nd Ed.: 2004-03

 
MECHANICAL
Case Dimensions, inches (mm) 16.7 (424) W x 5.2 (132) H x 17.5 (445) D
Weight41.8lbs / 19.0Kg
Mounting 19" Rack, 3RU
STANDARD MODELS
Model
Number		 Output
Power		 Output
Voltage 1, 2		 Input
Voltage		 SNMP 3
INV2450R-B 5kW - Continuous
10kW - Surge		 115VAC 24VDC Option
INV4850R-B 48VDC Option
INV2450RH-B 230VAC 24VDC Option
INV4850RH-B 48VDC Option
Notes:
  1. 115VAC models are shipped pre-programmed to 60Hz.
    230VAC models are shipped pre-programmed to 50Hz.
  2. 115VAC models can be adjusted between 100 and 120VAC.
    230VAC models can be adjusted between 200 and 240VAC.
  3. To specify the SNMP option add ‘S’ to the end of the model number, e.g. INV4850R-BS.